Linux Network: iptables

Andre Kurnia
4 min readJan 2, 2023

--

The way the Firewall works is quite simple. It creates a barrier between trustworthy and untrustworthy networks so your system can be safe from malicious packets. But how we are going to decide what is safe and what not? By default, you do get some privilege to set up rules for your Firewall but for more detailed surveillance of incoming and outgoing packages, IPTables are what you require the most.

IPTables can be used for personal computing or can also be applied to the entire network. Using IPTables, we will be defining a set of rules by which we can monitor, allow or block incoming or outgoing network packets.

Defining Chain Rules

Defining a rule means appending it to the chain. To do this, you need to insert the -A option (Append) right after the iptables command, like so:

sudo iptables -A

It will alert iptables that you are adding new rules to a chain. Then, you can combine the command with other options, such as:

  • -i (interface) — the network interface whose traffic you want to filter, such as eth0, lo, ppp0, etc.
  • -p (protocol) — the network protocol where your filtering process takes place. It can be either tcp, udp, udplite, icmp, sctp, icmpv6, and so on. Alternatively, you can type all to choose every protocol.
  • -s (source) — the address from which traffic comes from. You can add a hostname or IP address.
  • –dport (destination port) — the destination port number of a protocol, such as 22 (SSH), 443 (https), etc.
  • -j (target) — the target name (ACCEPT, DROP, RETURN). You need to insert this every time you make a new rule.

If you want to use all of them, you must write the command in this order:

sudo iptables -A <chain> -i <interface> -p <protocol (tcp/udp) > -s <source> --dport <port no.>  -j <target>

Once you understand the basic syntax, you can start configuring the firewall to give more security to your server. For this iptables tutorial, we are going to use the INPUT chain as an example.

Enabling Traffic on Localhost

To allow traffic on localhost, type this command:

sudo iptables -A INPUT -i lo -j ACCEPT

For this iptables tutorial, we use lo or loopback interface. It is utilized for all communications on the localhost. The command above will make sure that the connections between a database and a web application on the same machine are working properly.

Enabling Connections on HTTP, SSH, and SSL Port

Next, we want http (port 80), https (port 443), and ssh (port 22) connections to work as usual. To do this, we need to specify the protocol (-p) and the corresponding port (–dport). You can execute these commands one by one:

sudo iptables -A INPUT -p tcp --dport 22 -j ACCEPT
sudo iptables -A INPUT -p tcp --dport 80 -j ACCEPT
sudo iptables -A INPUT -p tcp --dport 443 -j ACCEPT

It’s time to check if the rules have been appended in iptables:

sudo iptables -L -v

It should return with the results below which means all TCP protocol connections from the specified ports will be accepted:

Filtering Packets Based on Source

Iptables allows you to filter packets based on an IP address or a range of IP addresses. You need to specify it after the -s option. For example, to accept packets from 192.168.1.3, the command would be:

sudo iptables -A INPUT -s 192.168.1.3 -j ACCEPT

You can also reject packets from a specific IP address by replacing the ACCEPT target with DROP.

sudo iptables -A INPUT -s 192.168.1.3 -j DROP

If you want to drop packets from a range of IP addresses, you have to use the -m option and iprange module. Then, specify the IP address range with –src-range. Remember, a hyphen should separate the range of ip addresses without space, like this:

sudo iptables -A INPUT -m iprange --src-range 192.168.1.100-192.168.1.200 -j DROP

Your virtual hosting server, your rules. Get all the resources you need for your next project.Get VPS Hosting

Dropping all Other Traffic

It is crucial to use the DROP target for all other traffic after defining –dport rules. This will prevent an unauthorized connection from accessing the server via other open ports. To achieve this, simply type:

sudo iptables -A INPUT -j DROP

Now, the connection outside the specified port will be dropped.

Deleting Rules

If you want to remove all rules and start with a clean slate, you can use the -F option (flush):

sudo iptables -F

This command erases all current rules. However, to delete a specific rule, you must use the -D option. First, you need to see all the available rules by entering the following command:

sudo iptables -L --line-numbers

You will get a list of rules with numbers:

Chain INPUT (policy ACCEPT)
num  target     prot opt source               destination1    ACCEPT     all -- 192.168.0.4          anywhere
2 ACCEPT tcp -- anywhere anywhere tcp dpt:https
3 ACCEPT tcp -- anywhere anywhere tcp dpt:http
4 ACCEPT tcp -- anywhere anywhere tcp dpt:ssh

To delete a rule, insert the corresponding chain and the number from the list. Let’s say for this iptables tutorial, we want to get rid of rule number three of the INPUT chain. The command should be:

sudo iptables -D INPUT 3

Step 3 — Persisting Changes

The iptables rules that we have created are saved in memory. That means we have to redefine them on reboot. To make these changes persistent after restarting the server, you can use this command:

sudo /sbin/iptables-save

It will save the current rules on the system configuration file, which will be used to reconfigure the tables every time the server reboots.

Note that you should always run this command every time you make changes to the rules. For example, if you want to disable iptables, you need to execute these two lines:

sudo iptables -F
sudo /sbin/iptables-save

--

--

Andre Kurnia
Andre Kurnia

Written by Andre Kurnia

Obsessed in cloud computing, Linux, tech infrastructure. Currently work as a Senior DevSecOps Consultant in Logicalis Group. Let's connect!

No responses yet